Rema REMA RL webbing lanyard 26 mm
REMA RL webbing lanyard 26 mm
€24,95 Incl. tax
Rema

REMA RL webbing lanyard 26 mm

EUR 24,95 Excl. tax
EUR 30,19 Incl. tax

REMA RL webbing lanyard 26 mm. Delivery in the Netherlands and across Europe. Request a SALESBRIDGES quotation.

In stock
3-4 days
Quantity
- +
Product description

REMA RL webbing lanyard 26 mm

The RL webbing lanyard has two loops and is available in three lengths. Select the length at SALESBRIDGES to suit the intended compatible system.

Features and application

  • 26 mm webbing with two loops.
  • For use with suitable connectors 1725001 and 1725002.

Technical specifications

Length 1.3 / 1.5 / 1.8 m
Webbing width 26 mm
Tested according to catalogue EN 354:2010

Available configurations

REMA article number SKU / article code Configuration
1724010 SB1724010 1.3 m
1724013 SB1724013 1.5 m
1724018 SB1724018 1.8 m

IMPORTANT SAFETY INFORMATION - general catalogue guidance

The following general information comes from PDF pages 2 and 3 of the REMA catalogue (printed pages 260-261). It concerns selection and use of a complete system and is not product-specific certification of this item.

Inspection, service life and withdrawal from use

  • Careless use can cause injury. Read the supplied operating instructions and safety information carefully before use.
  • Visually inspect before every use. Arrange and record inspections at least every 12 months in normal use and at least every 3 months in intensive use.
  • The catalogue recommends a maximum of 10 years from manufacture for ropes and lanyards, depending on frequency of use. A maximum of 10 years is also recommended for harnesses and equipment. This is not a guaranteed service life: damage, operating conditions and manufacturer instructions may require earlier replacement.
  • Have retractable fall arresters inspected and approved only by the manufacturer. Do not reuse harnesses or lanyards after a fall or when damaged; withdraw them from use immediately.
  • The rear arrest ring and front textile arrest loops are solely for connecting suitable fall-arrest lanyards. Use positioning eyes on an integrated or separate waist belt only where there is no danger of falling.

Selecting a harness, anchor and connecting system

  • Use a suitable fall-arrest harness where a fall hazard exists. A waist belt is for work positioning only and is not fall arrest. The catalogue describes positioning with a line around a mast to leave both hands free; only where there is no fall risk or a possible fall is less than 50 cm. This does not make a positioning belt suitable for arresting a fall.
  • Harness selection chart: rear attachment only - Light, Re-Line, Re-Line Plus or Re-Line Pro; front and rear attachment - Re-Line, Re-Line Plus or Re-Line Pro; front/rear plus positioning - Re-Line Plus or Re-Line Pro. Select the correct size, check the actual marked attachment points and use mutually compatible components with a suitable anchor.
  • Harness with lanyard and webbing energy absorber: for potential fall hazards with a movement radius below 2 m. For greater movement, the catalogue shows a guided rope grab on a working line or an appropriate retractable fall arrester with integrated absorption.
  • IMPORTANT: The webbing energy-absorber and webbing-connector configurations in the catalogue selection chart require at least 6.75 m of clear fall space measured from the attachment point. Do not automatically apply this figure to other devices: check product-specific clearance, system length, anchor position and manufacturer instructions.
  • For movement up to 2 m and insufficient height for the 6.75 m configuration, the chart names HWB-2K and HWB-2S. With sufficient height it names webbing connectors or lanyards with energy absorbers up to 2 m and suitable HWB/HPS/HRA devices. For greater travel it lists examples including HWB-3.5, HPS-6/12/18 and HRA-12/24, or KRG11. This is general selection guidance, not automatic approval for any particular workplace.
  • When using guided rope grabs, tie off the end of the working line or fit a suitable weight; this helps correct operation. Check the required combination of rope, rope grab and harness.

This general guidance does not replace the product-specific manual, risk assessment or competent system selection. Check all limitations and required clearance before use.

Delivery in the Netherlands and across Europe

SALESBRIDGES delivers these REMA products throughout the Netherlands and across Europe. Ask about current availability, lead time and the appropriate configuration.

Request a quotation from SALESBRIDGES

Contact SALESBRIDGES for product information or a quotation. Include the article code, configuration, quantity and delivery location.

E-mail: [email protected]
Phone: +31652883848

Product information
Brand Rema
Article code SB1724010
SKU SB1724010
EAN 9504882958288
What our customers say

average of 0 review(s)

No reviews found
Read or write a review
My account
You are not logged in. Log in to make use of all the benefits. Or create an account now.
Cart
Your cart is empty
Menu
Search
Search suggestions
No products found...