REMA EAP anchor clamp
REMA EAP anchor clamp. Delivery in the Netherlands and across Europe. Request a SALESBRIDGES quotation.
- Uitstekende kwaliteit
- Laagste prijs garantie
- Snelle levering
- More information? Contact us about this product
- Add to comparison list
REMA EAP anchor clamp
This EAP configuration provides an anchor for a suitable fall-protection system on an appropriate I-beam. SALESBRIDGES supplies the trolley and clamp as different product types.
Features and application
- Adjustable for different beam widths.
- Aluminium components and high-grade steel-alloy suspension eye.
Technical specifications
| Adjustment range | 63.5-305 mm |
|---|---|
| Maximum user load | 140 kg |
| Weight | 2.54 kg |
| Tested according to catalogue | EN 795-B |
Available configurations
| REMA article number | SKU / article code | Configuration |
|---|---|---|
| 1731803 | SB1731803 | EAP klem |
IMPORTANT SAFETY INFORMATION - general catalogue guidance
The following general information comes from PDF pages 2 and 3 of the REMA catalogue (printed pages 260-261). It concerns selection and use of a complete system and is not product-specific certification of this item.
Inspection, service life and withdrawal from use
- Careless use can cause injury. Read the supplied operating instructions and safety information carefully before use.
- Visually inspect before every use. Arrange and record inspections at least every 12 months in normal use and at least every 3 months in intensive use.
- The catalogue recommends a maximum of 10 years from manufacture for ropes and lanyards, depending on frequency of use. A maximum of 10 years is also recommended for harnesses and equipment. This is not a guaranteed service life: damage, operating conditions and manufacturer instructions may require earlier replacement.
- Have retractable fall arresters inspected and approved only by the manufacturer. Do not reuse harnesses or lanyards after a fall or when damaged; withdraw them from use immediately.
- The rear arrest ring and front textile arrest loops are solely for connecting suitable fall-arrest lanyards. Use positioning eyes on an integrated or separate waist belt only where there is no danger of falling.
Selecting a harness, anchor and connecting system
- Use a suitable fall-arrest harness where a fall hazard exists. A waist belt is for work positioning only and is not fall arrest. The catalogue describes positioning with a line around a mast to leave both hands free; only where there is no fall risk or a possible fall is less than 50 cm. This does not make a positioning belt suitable for arresting a fall.
- Harness selection chart: rear attachment only - Light, Re-Line, Re-Line Plus or Re-Line Pro; front and rear attachment - Re-Line, Re-Line Plus or Re-Line Pro; front/rear plus positioning - Re-Line Plus or Re-Line Pro. Select the correct size, check the actual marked attachment points and use mutually compatible components with a suitable anchor.
- Harness with lanyard and webbing energy absorber: for potential fall hazards with a movement radius below 2 m. For greater movement, the catalogue shows a guided rope grab on a working line or an appropriate retractable fall arrester with integrated absorption.
- IMPORTANT: The webbing energy-absorber and webbing-connector configurations in the catalogue selection chart require at least 6.75 m of clear fall space measured from the attachment point. Do not automatically apply this figure to other devices: check product-specific clearance, system length, anchor position and manufacturer instructions.
- For movement up to 2 m and insufficient height for the 6.75 m configuration, the chart names HWB-2K and HWB-2S. With sufficient height it names webbing connectors or lanyards with energy absorbers up to 2 m and suitable HWB/HPS/HRA devices. For greater travel it lists examples including HWB-3.5, HPS-6/12/18 and HRA-12/24, or KRG11. This is general selection guidance, not automatic approval for any particular workplace.
- When using guided rope grabs, tie off the end of the working line or fit a suitable weight; this helps correct operation. Check the required combination of rope, rope grab and harness.
This general guidance does not replace the product-specific manual, risk assessment or competent system selection. Check all limitations and required clearance before use.
Delivery in the Netherlands and across Europe
SALESBRIDGES delivers these REMA products throughout the Netherlands and across Europe. Ask about current availability, lead time and the appropriate configuration.
Request a quotation from SALESBRIDGES
Contact SALESBRIDGES for product information or a quotation. Include the article code, configuration, quantity and delivery location.
E-mail: [email protected]
Phone: +31652883848
| Brand | Rema |
| Article code | SB1731803 |
| SKU | SB1731803 |
| EAN | 9509872324593 |